Expert Answers about Hitch Fabrication Parts

• Where In The USA Is The Curt Cargo Carrier For 2" Hitches, Part # C18152, Made
• The 24x60 Curt Cargo Carrier for 2" Hitches - Steel - 500 lbs, part # C18152, is engineered, fabricated, welded, finished, tested, and shipped out their facility in Eu Clair, Wisconsin. I have included a video review link below.
  view full answer...


• Where is the Curt A25 Trailer Hitch Manufactured?
• Curt is based in Eau Clare, WI. All materials are fabricated in the USA, but Curt says that some hitch materials may be imported. The Curt A25 5th Wheel Trailer Hitch for Ford Towing Prep Package # C16036 is produced in the USA. However, if you wish to have a part that has all parts manufactured in the USA, the B&W Companion OEM 5th-Wheel Hitch for Ford Super Duty Prep Package - Dual Jaw - 20,000 lbs # BWRVK3300 is the 5th wheel hitch for you.
  view full answer...


• Awning with Roller Bar for 2007 Keystone Raptor Toy Hauler
• The Solera 18' Solid Black RV Awning Roller and Fabric (Std) # LCV000211506 does come with the roller as well as the fabric. It does not come with any of the other supplies like support arms or heads. These Solera awnings are compatible with other manufacturers parts, so you should not have any fit issues with your 2007 Keystone Raptor Toy Hauler.
  view full answer...


• What Material is Hook and Strap Made Of on Fulton Heavy-Duty Winch Strap with Hook # FWS20HD0200
• On the Fulton Heavy-Duty Winch Strap with Hook, part # FWS20HD0200, the hook is a forged zinc-plated steel material. The catch and the spring are zinc-plated. The yellow fabric, which is the strap, is a heavy-duty nylon webbing material that is similar to the material used in automotive seat belts.
  view full answer...


• Material of License Plate Bracket Included with Hopkins Smart Hitch Backup Camera
• The license plate bracket (Part C) of the Hopkins Smart Hitch Backup Camera # HM50002 is made of 1/2 inch plastic so cutting it wouldn't cause any camera issues. Although it might not be necessary. The camera can easily be detached from the bracket and the sensors can be too using a screw driver. So it might work better for you to install it this way.
  view full answer...


• Has ADCO Made Any Changes to the Material They Use For Their Covers
• ADCO did recently make changes to the fabric they are using on their RV covers. They switched from the Tyvek material to an Olefin material. The Adco Olefin HD All-Climate + Wind RV Cover for Travel Trailer # AD47ZR would be the correct cover for a 20' travel trailer. According to ADCO, the new fabric offering is part of the company’s popular All Climate + Wind Designer Series and is an improved replacement for the previous All Climate option. Designed for protection from sun, rain, snow...
  view full answer...


• Parts Needed to Install Solera Awning and Material
• There are a few more products you would need to complete a 16 foot awning with part # LCV000231520. The material is 500 x 500 fabric denier at 13.5 ounces per square yard of vinyl/woven acrylic material. You will need the Solera Manual Pull Style Awning Drive Head # LC271181 Solera Manual Pull Style Awning Idler Head # LC272397 Solera Rollbar Only For 16' White Awning # LC260560357 Solera Manual Awning Pull Strap # LC292794 Solera 63" Short Awning Support Arm # LC97UD We don't have pictures...
  view full answer...


• How are the Fan Blades of the Derale 18 inch Rigid, Steel-Blade Race Fan, part # D17318 Made
• I spoke with my contact at Derale and he informed me that the steel blades of the Derale 18 inch Rigid, Steel-Blade Race Fan - Belt Driven - 8,000 RPM, part # D17318, are made from stamped steel. If you wanted a fan that features stainless steel blades, and flattens out when sufficient airflow is present, therefore increasing fuel mileage and power I would recommend a Derale 18 inch Heavy-Duty, Stainless Steel Flex Fan, part # D17018.
  view full answer...


• Quality Car Cover for 2016 Hyundai Sonata to Protect Vehicle from Outdoor Elements
• The Rampage 4-Layer Outdoor Vehicle Cover # RA1304 features a heavy-duty spunbond outer layer that works to shed water and protect your car against the sun and heat. The additional layers further protect your car from the elements, yet they are breathable and allow moisture to escape from under the cover. The vehicle cover has a 90-day warranty and is the most economical cover we offer for your 2016 Hyundai Sonata. For a cover that offers a higher quality design, I recommend the Covercraft...
  view full answer...


• American-Made Trailer Hitch for 2012 Acura MDX
• I'd recommend the Curt Class III Trailer Hitch, part # 13354. Curt manufactures their hitches in the USA. Draw-Tite is an American owned company, but their hitches are manufactured in Mexico. If you'll be using the hitch for towing purposes, you'll need a few more parts to complete your towing system: Trailer wiring harness with 4 pole trailer connector, part # 118424 Ball mount, part # 2923 Trailer ball, part # 19261 for a 1-7/8 inch or # 63845 for a 2 inch.
  view full answer...


• Is There a Weld Stop On the Curt Hitch part # C11405
• The hitch tube of the Curt hitch part # C11405 that you referenced is totally open all the way through. You may also be referring to the weld stop that some Class I hitches install in the tube to prevent the use of Class II accessories in them. Curt hitches do not have that. Curt requires the use of their stabilizer strap part # 18050 when using their hitch to carry a non-supported load like a bike rack. I attached a review video for you to check for the strap as well.
  view full answer...


• Where is the Draw-Tite Hitch Receiver Lock BD580412 Made?
• The Draw-Tite Hitch Receiver Lock - Extra Long - Flush Design part # BD580412 is manufactured in China. For an alternative that is made in the United States I recommend using the InfiniteRule Hitch Lock for 2-1/2" Hitches - 3-1/8" Span - Stainless Steel part # 34061072-D for 2.5" hitch applications and the InfiniteRule Hitch Lock for 3" Hitches - 3-7/8" Span - Stainless Steel part # 34061074-D for 3" hitch applications. These are both made here in the United States and will offer...
  view full answer...


• Where is the Draw-Tite Hitch for a 2007 Ford F-150 Made
• The Draw-Tite Max-Frame Trailer Hitch Receiver part # 75506 which is a fit for a 2007 Ford F-150 is made in Mexico. If you are looking for a USA option, the Curt Trailer Hitch Receiver part # C13360 is the way to go. If you need a trailer connector to go along with the trailer hitch, the Curt T-Connector Vehicle Wiring Harness part # C56031 is plug-n-play.
  view full answer...


• Anti-Rattle, locking, Stabilization Pin that will not Rust
• I have just what you need, a stainless steel locking anti-rattle hitch pin for you. I suggest the Stainless Steel Locking, Anti-Rattle Threaded Hitch Pin for 2" Trailer Hitches part # SR25219. You will need a hollow shank for this to work. For a solid shank, you will want the Andersen Trailer Hitch Lock part # AM3493 for the lock in addition to our Brophy Stabilizer Bracket part # RHSB for anti-rattle.
  view full answer...


• Is the Curt Class III Ball Mount with 2-5/16" Ball - 2" Drop - 7,500 lbs Made in USA
• The Curt Class III Ball Mount with 2-5/16" Ball part # C45041 is not made in the USA but we do have options that are like the B&W Heavy-Duty Ball Mount part # BWBMHD30010. This is not a complete kit though so you'd also need to add the 2-5/16" Hitch Bal part # BWHB94050 and Gen-Y Hitch Pin and Clip for 2" Hitches part # 325-GH-096. This setup is over twice the price of the one you picked out and requires you to still torque the hitch ball but it's made up of all USA components.
  view full answer...


• Is the Buyers Products Tri-Ball Hitch Made In the USA
• The Buyers Products Tri-Ball Hitch part # 3371802205 is made overseas but we do have a made in USA alternative, the Gen-Y 3-Ball Mount for 2" Hitch Receivers part # 325-GH-054.
  view full answer...


• Is the Torklift Trailer Hitch TLF1002-30 Made in the USA
• The Torklift Hitch part # TLF1002-30 that you referenced is made in the USA.
  view full answer...


• Whats Included with the Florida Gators Trailer Hitch Receiver Cover Part CTH4S
• The Florida Gators receiver cover # CTH4S won't include a hitch receiver lock or hitch pin and clip, but I certainly would recommend one such as the Master Lock # 1480DAT. The pin and clip is part number # PC3 and will fit 2 and 2-1/2 inch receiver hitches. For 1-1/4 inch receivers the hitch pin and clip # PC2 and hitch receiver lock # e98880 would work great. They both have a pin diameter of a 1/2 inch. I included a few video reviews for you too.
  view full answer...


• Tools Needed to Install EcoHitch Trailer Hitch Receiver on a 2016 Subaru Outback
• I've linked an install video of the EcoHitch, part # 306-X7601, being installed on a 2016 Subaru Outback for you. The tools you need are: Phillips and flat head screwdrivers Ratchet with 10 mm socket Trim Remover, part # ALL648544 Mallet Utility Knife Tape Measure Grease pencil Straight edge Torque Wrench, part # ALL644044
  view full answer...


• Is the Hidden Hitch Trailer Hitch Extender # he18 Solid or Hollow
• The Hitch Extender, # he18, is hollow at both ends so that would be tubular steel. The use of a hitch extender will reduce the capacity of the trailer hitch by 50 percent. If the hitch started with a 350 pounds tongue weight capacity, by using this extension that amount will be reduced to 175 pounds.
  view full answer...